변류기 사용 원리
1) 변류기의 배선은 직렬 연결 원리를 따라야 합니다. 즉, 1차 권선은 테스트 중인 회로와 직렬로 연결되어야 하고, 2차 권선은 모든 기기 부하와 직렬로 연결되어야 합니다.
2) 측정된 전류에 따라 적절한 변환비를 선택합니다. 그렇지 않으면 오차가 증가합니다. 동시에 절연이 파손되면 1차측의 고전압이 2차측의 저압측으로 유입되어 인명 및 장비사고의 원인이 되지 않도록 2차측의 한쪽 끝을 접지해야 합니다.
3) The secondary side is absolutely not allowed to open circuit, because once the circuit is open, the primary side current I1 will all become magnetizing current, causing φm and E2 to increase sharply, resulting in excessive saturation magnetization of the iron core, serious heat generation and even burning of the coil; , which increases the error. When the current transformer is working normally, the secondary side is used in series with current coils such as measuring instruments and relays. The impedance of the current coils such as measuring instruments and relays is very small, and the secondary side is similar to a short circuit. The magnitude of the CT secondary current is determined by the primary current, and the magnetic potential generated by the secondary current balances the magnetic potential of the primary current. If the circuit is suddenly opened, the excitation electromotive force will suddenly change from a small value to a large value, and the magnetic flux in the iron core will present a severely saturated flat-top wave. Very high peak waves, whose value can reach thousands or even tens of thousands of volts, endanger the safety of workers and the insulation performance of the instrument.
또한 2차측의 개방회로는 2차측의 전압을 수백 볼트에 이르게 하여 만지면 감전사고의 원인이 됩니다. 따라서 변류기의 2차측에 단락 스위치가 장착되어{0} 2차측이 개방되는 것을 방지합니다. 사용과정에서 일단 2차측이 개방되면 즉시 회로부하를 제거하고 정전처리를 해야 한다. 모든 것을 폐기한 후 재사용할 수 있습니다.
4) 계측기, 계전기 보호, 차단기 고장 판정 및 고장 필터링 등의 요구를 충족시키기 위해 모든 회로는 발전기, 변압기, 나가는 선로, 모선 차단기, 모선 차단기, 바이패스 차단기에 설치됩니다. 및 기타 회로. 2차 권선이 있는 2~8개의 변류기.
5) 보호 변류기의 설치 장소는 주 보호 장치의{1}비보호 영역이 없도록 최대한 멀리 설정해야 합니다. 예를 들어, 두 세트의 변류기가 있고 위치가 허용하는 경우 회로 차단기가 교차 보호 범위 내에 있도록 회로 차단기의 양쪽에 설치해야 합니다.
6) 필라형 변류기의 부싱 섬락으로 인한 부스바 고장을 방지하기 위해 일반적으로 변류기는 차단기의 출력 라인이나 변압기 측에 배치됩니다.
7) 발전기의 내부고장으로 인한 손상을 줄이기 위하여 여자장치의 자동조정에 사용되는 변류기는 발전기의 고정자권선의 출력측에 배치되어야 한다. 발전기가 시스템에 통합되기 전에 분석을 용이하게 하고 내부 결함을 찾기 위해 측정 기기에 사용되는 변류기를 발전기의 중성 측에 설치해야 합니다.
